Tarafdar, Suranjan

Suranjan Tarafdar hails from Manikganj, Bangladesh. He completed his S.S.C  from Dakshin Jamsha High School  Manikganj in 1991, and H.S.C  from Govt. Science College, Dhaka in 1993. He obtained a B.Sc in Mechanical Engineering  from BUET in June 2000. Afterwards, he flew to Germany and got an M.Sc in Mechatronics from the University of Siegen, Germany. He did an internship at Rolls Royce,Germany (An aero-engine manufacterer). He did his Master's thesis at Siemens VDO Automotive AG. Since July 1, 2005  he started working there as a Research and Development Engineer. In July 2007, Continental AG of Germany  acquired Siemens VDO from Siemens AG. However, his working area in Continental AG  remains same.
Continental AG, Germany

Back to Top

Quasem , Mahmud

hello, I am from Bangladesh and completed my undergraduate degree in mechanical engineering from BUET before starting my career as Engineer to work in software development. I decided to enhance my engineering skills and landed in Stuttgart and then move to Siegen to undertake a Master of Science in Mechatronics. During my studies I got an opportunity to work at German Aerospace Center in Munich as a part-time employee and did my Master thesis here. After successful completion of my Master thesis, I then move again to Siegen in June 2006 to join at Mechanical Engineering Department, University of Siegen to work as a research assistance  (Wissenschaftlicher Mitarbeiter ) with professor P. Betch.
University of Siegen, Germany

Back to Top


Islam , Kamrul

Kamrul Islam Soheb is from Jhalukathi. His S.S.C  and H.S.C were  from Udbodhon Madhyamik Bidyalay, Jhalukathi and Tejgaon College, Dhaka respectively. He holds a B.Sc in Mechanical Engineering from BUET and an M.Sc from the University of Siegen, Germany. He has been working at  Integrated Dynamics Engineering GmbH  as a system engineer ,vibration control since April, 2008.
Integrated Dynamics Engineering GmbH, Germany

Back to Top


Hossain , Khondokar Zakir

Khondokar Zakir Hossain was born in Naogaon and went to Raninagar Pilot High School, Naogaon and Rajshahi Govt.City College, Rajshahi. He obtained B.Sc in Mechanical Engineering from RUET and M.Sc in Mechatronics from the University of Siegen, Germany. He is now teaching at the World's University of Bangladesh, Dhaka on various Mechatronics areas.
World's University of Bangladesh

Back to Top


Banik , Sajal Chandra

Sajal Chandra Banik comes from Narsingdi. He obtained a B.Sc in Mechanical Engineering from BUET and an M.Sc in Mechatronics from Technical University of Hamburg-Harburg, Germany. Afterwards, he joined CUET as an Assistant Professor. Currently he is doing a PhD at Saga University, Japan.
Saga University, Japan

Back to Top


Alam, Shafiqul

Shafiqul Alam Sohel is from Naogaon. He passed S.S.C from Dhamoir hat Shafia High School, Naogaon in 1993 and H.S.C from New Govt Degree College, Rajshahi in 1995. He got a B.Sc in Mechanical Engineering from IUT, Gazipur, Dhaka. He did his M.Sc  in Mechatronics at the University of Applied Sciences, Weingarten, Germany. He has joined PMDM GmbH as a Hydro Bearing Design Engineer in September 18, 2006..
PMDM GmbH, Germany

Back to Top

Saifullah, Abul

Abul Saifullah did his schooling at Ideal School, Dhaka  and college education in Notre Dame College,Dhaka. After he had finished his H.S.C, he continued with his engineering studies in BUET and got a B.Sc in Mechanical Engineering from there. He went to South Korea to pursue his higher studies and obtained an M.Sc in Mechatronics from Gwangju Institute of Science and Technology. Now, he is doing his PhD at Industrial Research Institute, Swinburne University of Technology, Australia.
Swinburne University of Technology, Australia

Back to Top


Alam , Shamim  Mohammad

Mohammad Shamim Alam came from Tangail. He completed  his high school education in Tangail and college education in Dhaka College, Dhaka. Then he entered into BUET and obtained his Bachelor's in Mechanical Engineering. He pursued his higher studies in Germany and obtained an M.Sc in Mechatronics from the University of Siegen.

Back to Top


 Chowdhury, Sanjib Chandra Dr.

Dr. Sanib Chandra Chowdhury is currently a lecturer at the Mechanical Engineering Department in BUET. He did his B.Sc and M.Sc in Mechanical Engineering from the same university. He achieved  a PhD degree in Mechanical Engineering from a Japanese University.
Bangladesh University of Engineering & Technology, Dhaka

Back to Top

Mahmudul Huq

Mahmudul Huq was born in Dhaka. He completed his S.S.C and H.S.C in 1996 and 1998 respectively. He did his B.Sc. at London Metropolitan University, Dhaka  in 2001. Mahmudul Huq finished his M.Sc. in Computational Science at Technical University of Braunschweig, Germany. Currently, he is working as research associate at University of Siegen.
University of Siegen

Back to Top


Dewan Khaledur Rahman

Dewan Khaledur Rahman (Sumon) comes from Sylhet. He  completed his B.Sc in Mechanical Engineering from Chittagong University of Engineering and Technology (CUET) in 2006. Now he is pursuing his masters in Mechatronics at University of Siegen, Germany.
University of Siegen

Back to Top





Copyright © 2006 Mechatronics Society of Bangladesh                                                                          Last modified On Donnerstag Juli 05, 2012